Poolife Stain Lift

All Products

Poolife Stain Lift
Poolife Stain Lift

Poolife Stain Lift

Price

$32.99 $0.00
( / )
DESCRIPTION Poolife Stain Lift is a highly concentrated stain remover for swimming pools. Works on copper, iron, manganese, cobalt and silver staining. Can be used on gunite, most plaster, concrete, vinyl and fiberglass. DOSAGE 2.5 lb per 20,0000 gallons of water. DIRECTIONS This product can be used on several pool...
  • 2.5lb single
  • 2 pack
  • 4 pack
Inventory:

1 in stock.

DESCRIPTION

Poolife Stain Lift is a highly concentrated stain remover for swimming pools. Works on copper, iron, manganese, cobalt and silver staining. Can be used on gunite, most plaster, concrete, vinyl and fiberglass.

DOSAGE

2.5 lb per 20,0000 gallons of water.

DIRECTIONS

This product can be used on several pool surfaces including gunite, most plaster, concrete, vinyl and fiberglass. This product is not intended for use on pools with black plaster.

  1. Brush the affected areas.
  2. Adjust pool ph between 6.8 and 7.2 allow chlorine or bromine level to drop less than 2 ppm.
  3. Slowly broadcast or apply Poolife Stain Lift directly into the pool at a rate of 2.5 lb of this product to treat up to 20,000 gallons of water.
  4. Concentrate the application along the pool walls and especially in the areas where stains are most prevalent.
  5. Concentrate the application along the pool walls and especially in the areas where stains are most prevalent.
  6. Allow the circulation system to run continuously for 24 hours.
  7. After 24 hours, adjust the pH levels to the normal 7.4 to 7.6 and total alkalinity 80 to 120 ppm ranges. Maintain normal sanitizer levels.
  8. Do not apply shock treatments for at least 72 hours.
  9. To prevent stains from returning, follow treatment with Poolife Stain Stop.

Note: Most stains are easier to remove when they are fresh. Old stains or those deeply set may require a second treatment. Applying Poolife Stain Lift directly to the affected area may be needed for stubborn stains. Not all swimming pool stains are metallic in nature. Stains from oils, vinyl liner fungus, leaves, algae and other organic matter may not be significantly affected by Poolife Stain Lift. See your Poolife dealer for recommendation on treating these types of stains.

For more information on Pool Life products, please watch this informational video.

PRODUCT FAQ'S

Algae are microscopic plants that grow in water. They are usually green, but can also be blue-green, black, yellow or mustard. Algae can grow on the pool surface or float in the water. Algae can turn pool water green, which can literally happen overnight.

 You need to shock your pool water when opening and closing your pool. You should also shock treat weekly during the pool season to kill bacteria and algae and remove contaminants. We recommend shocking at the same time and on the same day each week. The optimum time to shock your pool is sundown. At this time of the day, the chlorine can work without fighting the sun’s ultraviolet rays. The pool should be left uncovered after shocking the pool. Shocking after sundown also gives chlorine more time to restore the water clarity.

If this happens, use Poolife® Back to Blue® Shock System, which can restore water clarity in 24 hours. To treat common algae like green and yellow, use Poolife® Algae Bomb® 30, Poolife® Defend+® or Poolife® Super Algae Bomb® 60 algaecides, which, when used in conjunction with a Poolife® shock product, cleans up both green and yellow algae. Mustard and black algae are more difficult to remove, so we recommend using Poolife® Mustard Algae Treatment product or Poolife® AlgaeKill II product. Poolife® has additional algaecides to address other specific needs. Always follow product label directions carefully.

The build-up of cyanuric acid in swimming pool water resulting from the use of stabilized sanitizers in conjunction with stabilized shock products. • Overstabilization will significantly decrease the effectiveness of chlorine in killing bacteria and algae. • Small levels of cyanuric acid (20–50 ppm) do serve a purpose in protecting chlorine from sunlight degradation. However, too much will negate any benefit and cause problems. • Calcium Hypochlorite-based shock products such as Poolife® TurboShock® , and Poolife® Rapid Shock® shock treatments will not increase the stabilizer level in your pool.

 Always add stabilizer before adding Poolife® chlorinators. The stabilizer must be added slowly through the skimmer while the pump is operating.Allow at least 48 hours for the stabilizer to dissolve before backwashing or cleaning the filter.

 The cyanuric acid level and the climate determine whether you need to add stabilizer to your pool. You should take a sample of your pool water to your Authorized Poolife® Dealer for a detailed analysis and recommendation or you can use test strips to determine the stabilizer level. When opening your pool, if you choose to use stabilizer, the stabilizer level should be 20–50 ppm. During the swimming season, the ideal stabilizer level should be maintained between 20–50 ppm. Chlorine isn’t as effective if the stabilizer level rises above 90 ppm. Remember some chlorinators add stabilizer as the chlorine dissolves into the water.